Prev iATN Members TechHelp for August 19, 2008
Automotive Technical Exchange for the Automotive Repair Professional		 Next
(Also Available: All, Asian, Chrysler, European, Ford, GM.)
Vehicle Owners: If you are seeking an automotive repair professional to service your vehicle, visit the iATN Repair Shop Finder.

Open Help Requests for All Makes and Models
Help Request Answers
1996 Acura Integra 1.8L instrument cluster indicator lights
Here's the deal. This integra has instrument cluster indicator lamps that stay on with the car off and all. Sometimes the door chime will be on for no reason at all. This only happens when it rains. The car has a water drip on the driver's clutch pedal area su...		 View
2001 Audi A4 1.8L engine oil
Hello group, I have this Audi that makes a loud lifter clatter or chain rattle from the valve train only after the engine is warmed up and below 1500 rpm. Cold start has a small rattle and then goes away. I have read several TSB's on these issues but have no ...		 View
1999 BMW 528i 2.8L Loss of Can Comm. ABS lite comes on, Speedometer q
Start vehicle & go thru a complete drive cycle. Shut vehicle off for 5 to 10 min. Then restart, as soon as you put in gear to take off-message appears-(Transmission fail safe mode) the ABS Lite comes on,speedometer quits working,check engine lite comes on, and...		 View
2001 BMW 740iL 4.4L starter
This car came to me with a no start. I have B+ at the starter but neither of the solenoid wires would power up when i turned the key so i went to the starter relay i swore that i had all the proper voltages yesterday, also all-data says that the relay is under...		 View
2001 BMW 325i 2.5L cooling fan
We have tried disconnecting a/c pressure sensor, radiator outlet temperature sensor,fan module checks okay. Alldata wiring and system function information inadaquate.We are unable to determine what information the ECM uses to operate the cooling fan system.		 View
2002 BMW 325i 2.5L cooling fan
Good morning BMW techs.I have a problem with this car.It came in overheating.Trouble code 125.cooling fan.replaced fan sensor in the lower rad hose and the cooling fan,wires were rotted off behind module,Fan still does not work. I have power and ground to the ...		 View
2001 Chevrolet Monte Carlo 3.8L suspension
Good morning to all.I have this 01 monte carlo ss that when making tight turns (like a parking lot type turn) there is a loud snapping type noise.The wheel must be turned either all the way or just about all the way.Noise happens aprox. 1/2 way thru a 180 turn...		 View
2002 Chevrolet Corvette 5.7L MIL Lamp on
I got this Corvette with the MIL on with codes P0410 & P1415 for the AIR system. The first thing I did was check the function of the AIR pump & vacuum solenoid control valve with the Tech2. Both work fine. Removed the hose at the pump to test output of the pum... Trouble codes: p0410 (secondary AIR injection system), p1415 (secondary injection system bank 1).		 View
2005 Chevrolet Silverado 5.3L Misfire
i had this truck brought in by a used car dealer,check engine lt flashing, running terrible,missfire #1#2#8 cyl's. #2 had cracked sparkplug,replaced and ok. #1 changed plug, wire,coil switched and injector changed, still miss at idel mainly.compression 125lbs....		 View
1991 Chrysler New Yorker Fifth Avenue 3.3L ECM & power Supply
Car sets three days and battery gose dead. Checked all interior lights, trunk, under hood and glove box and even removed fuse. Still a drawl. I've searched for simular problem and found no fixes. My car is not going away, I have to fix it! What I've found at t...		 View
1995 Chrysler Cirrus 2.5L No Start
I have this car that originally would just stall, and die I could never catch it in the act, now the car will not start, no spark after lots and lots of testing and the customer helping from the internet I am stumped. I have no spark, I have RPM both Cam and C...		 View
1998 Chrysler Town & Country 3.8L No Start, Hesitation, Cuts out, Stall, MIL Lamp on
chrysler techs please help.have this 98 tnc that wants to beat me.came in with complaint of stalling/hard restart,mil flickering.upon inspection the van died and the asd relay and fuel pump relays began rapid firing.swaped with new oe relays eith no change.usi...		 View
2002 Chrysler Sebring 2.4L no communication, no bus
Help, this car was towed in with a no start condition. on the instrument cluster where the speedometer is it says no bus. im not real familiar with chryslers. what does this mean? sorry to sound so stupid. fuses are good and it has a new battery. it will not c...		 View
2001 Daewoo Lanos 1.6L No Start
Hello everybody, this car came in as a no start. I have traced it to a problem with the PCM not pulsing the injectors. All injectors have battery voltage to them, but computer will not pulse to ground. I have check the wires between the PCM and injectors, all ...		 View
1993 Dodge Caravan 3.3L cooling fan
this 93 caravan originally came in because it was overheating. i found that it was way low on coolant because of a leaking water pump so i replaced it. it came back a few weeks later overheating again. this time i found a blown fusible link, so i replaced the ...		 View
2004 Dodge Caravan 3.3L Reference
Hi Chrysler techs. The issue I am having with this van is a no start/no crank condition. I have no communication with the PCM, TCM, or the ABS module. There is no fuel pump operation, no reference voltage at any of the CKP, CMP, MAP... etc. There is no check e...		 View
2005 Dodge Durango 4.7L Engine
Any help on this would be helpful. Vehicle makes a knocking noise while running from what sounds like the flywheel area of the motor when the brake is applied! Shift into a gear and the noise is present all the time. Shift into park and release the brake...noi...		 View
1990 Ford Aerostar 4.0L instrument lighting
This van has a problem unlike the other ford electronic instrument clusters. Usually we see these with dim lighting all the time and that is the only lighting problem we run into with these vans. This van when started will have nice bright dash lights and afte...		 View
1994 Ford Ranger 4.0L MIL Lamp on
Customer brought vehicle in starting check engine light coming on going up hills when cresting hill light goes off. We did all the basic checks everything checked out ok. When we check for codes no codes in system on koeo and koer tests. Road tested to confirm...		 View
1995 Ford Econoline 7.5L Surge, Misfire
Vehicle came in with a misfire/surge at around 40-45 mph when it warms up. The 172 code shows only under koer test. I did add a ground to pin 49 o2 ground at the pcm because the o2 voltage on my scoped stayed at 1.5 volts. And to let you know, the datastream a... Trouble codes: 512 (kam), 172 (o2 not switching).		 View
1997 Ford Ranger 2.3L Excessive Emissions, Poor Idle Quality, Stall
Hello out there in Tech land! This one seemed easy enough with the codes it has. The upstream O2 is rich most of the time. It will start to switch when you drive down the road. I have good voltage and ground to the O2 heater, and when I ohm check the heater ... Trouble codes: P0135 (o2 heater malf. b1s1), P0141 (02 heater malf b1s2), P1132 (os insufficient switching b1s1), P1138 (o2 insufficient switching b1s1 koer), P1408 (egr flow out of range).		 View
1999 Ford Explorer 4.0L Liftgate
Problem is simple-broken ball studs on liftgate strut mounts.[rear door]What Im looking for is a better solution for repair.Ford wants silly money for the mounts and I wondered if any of you body guys have found them elseware.This door weighs a ton and I dont ...		 View
2000 Ford Windstar 3.0L transmission
i can drive this vehicle 3-5 minutes and the tranny works fine,then the pump starts to whine and seems like it goes into neutral.shut vehicle off wait not even a minute and take off again for a couple minutes.any help would be greatly appreciated.		 View
2000 Ford Excursion 7.3L coolant contaminated w/fuel
can anyone suggest possibilities for diesel fuel - in coolant resevior & spraying out of cap - while engine is running - ie - i think its a fuel injector sleeve i would think - any ideas		 View
2000 Ford ZX2 2.0L Cam Timing & Rough Idle
Thanks to all that reply. I know how frustrating some of these cars can be and this site helps all of us. Well it all started when the customer brought the car in on the hook and then explained to me what had happened. As he was driving the car it just felt li...		 View
2001 Ford Ranger 2.3L Whole vehicle
Hello, Thank you for reading through the issues as I see them. I am the happy recipient of two Ford Ranger EVs (electric vehicle). The Iatn request for help requires and engine and transmission selection and automatically inputs the ignition and fuel system. T...		 View
2002 Ford F-650 7.3L compressor wiring
I need a wiring diagram for this F-650 a/c system. The customers mechanic cut alot of wires to the compressor and relays. Alldata doesn't cover the F-650, and I am not going to guess at this mess. Thank you in advance for any diagram you can provide.		 View
2003 Ford F450 Super Duty 6.0L Cooling Systems
Hello, I have I prob that I am getting coolent in the oil pan. The eng runs fine. has no skip. no codes in system. have removed the oil cooler and egr cooler and found no reson to have coolent in oil pan. It will run in as fast as you can poor it in. has anyon...		 View
2004 Ford Pickup 4.6L axle/diff
thanks for all the help in the past. have a truck that was droped off from body shop.truck was hit hard on left rear complete rear differental was replaced due to damage. truck is here for bad vibration at a very low speed 1-3 mph rear of truck will shake real...		 View
2008 Ford escape 3.0L Alignment
We have a 2008 Escape with 35k miles, all 4 tire are worn hard and chopped on the inside edge, suspension is tight and alignment looks good, it drives ok once you get past the tire noise! thanks in advance for any input,		 View
1999 GMC Suburban 5.7L Door Lock Actuator
Would certainly appreciate any help I could receive on this problem. The locks on the vehicle will not fully lock or unlock. You can hear the locks making the familiar click sound, but they only move about 1/16 of an inch at the most. All door lock actuators w...		 View
1999 GMC Pickup 7.4L Hesitation, Surge, Cuts out, Misfire
Engine cuts out and stumbles intermittently under load. road test with data shows ft enable dropping to no periodically, especially when stumble occurs. I know i need to replace fuel pump, but that is not the intermitent. Anyone know what "ft enable" means. Al...		 View
2003 GMC Yukon 5.3L MIL Lamp on
tps1 signal .81 volts tps2 .71 volts ref voltage problem on tps2 4.28v tps1 refv 4.91 checked power and grounds all good if i unplug actuator ref voltage 5.01 on both ref if i swap ref voltage wires 1 and 2 pins or cut wires and swap both are 4.83 is problem i... Trouble codes: p2135 (throttle sensors 1 and 2 disagree).		 View
2003 GMC Yukon 6.0L Stall
We have a wierd problem here, this truck cranks up and runs fine in park or neutral, but as soon as it is put in gear the truck dies immedietly, every time. Scaned computer and it has no codes. This is a drive by wire throttle body and I have asked other techs...		 View
1996 Honda Civic 1.6L Hesitation, Surge
Hello,and thank you for taking time to read my help request.This Honda is shortening my life expectency,as you can see it came in originally for a cylinder head gasket repair.Everything was fine up until approximately 1000kms after vehicle left,customer stated...		 View
1999 Hyundai Bering 638CID Mechanical
Hey guys looking for help on this 638 detroit diesel.Leaking oil from in between engine and transmission removed trans found seal silicone seal reassemble still leaking anything i should know please help		 View
2001 Isuzu Rodeo 2.2L Timing Belt
Hello to all, I have a 2001 Izusu Rodeo that we have replaced the timing belt, crank timing pulley, crank seal, cam seals, both idlers and tensioner pulley due to a whirring noise in front of engine. We also replaced the water pump because we were right there....		 View
2000 Jaguar S-Type 4.0L Timing chain
Hello all, I am looking for a little insight. This Jag came in in the hook for a no start. The complaint was that he parked it and the next morning it wouldn't start, just spin very fast. Compression was low at 20 psi so we squirted oil in the cylinders and th...		 View
2003 Jaguar X-Type 2.5L MIL Lamp on
Hello everyone, This engine caries two knock sensors, one under the intake manifold (engine top)and one on the side of the engine (engine side). ALL DATA & SHOPKEY show the location of the one under the manifold only and I have spend hours looking for the othe... Trouble codes: P0333 (knock sensor).		 View
2001 Land Rover Discovery 4.0L Misfire, MIL Lamp on
hey there techs, i have this vehicle with an intermittent misfire at start-up on cyl 3 after you rev it a few times it goes away. vehicle came to us after another shop had chaned the plugs, wires, both coils, even the #3 injector, and intake plenum gasket. i d... Trouble codes: p0303 (cyl. 3 misfire).		 View
2002 Land Rover Freelander 2.5L Head bolts
We are replacing headgaskets on this Land Rover and want to get some reassurance on the torque settings for the headbolts. Alldata and Mitchell both show 18 ftlbs, 18 ftlbs, 18 ftlbs, the additional 180 degrees. We want to make sure its 18ftlbs then to 36ftlbs...		 View
1995 Mazda Millenia 2.5L wiring
This came in with engine will not shut off. If I pull the door lock fuse all is ok. I disconnected stereo (bose) pcm, abs, srs relays, body control module that piggybacks the fuse box. the door lock wire, wht/ green feeds voltage to blk/ wht wire from engine f...		 View
1995 Mazda 626 2.0L No Start
car came in no start fuel pressure ok, noid ok, no spark, check eng light on. voltage to coil + side ok. replaced dist. same thing triple check fuses voltage . clean all grounds i can or find ran more no good. being bit before I've tried 5 dist new reblt used...		 View
1996 Mazda 626 2.5L Hesitation, Stall, MIL Lamp on
I have this Mazda that is giving me major problems!! It will not rev up at all!! It almost acts like a restriceted exhaust. I have ran back pressure checkes, normal; compression checks, 110-120; fuel pressure, 45-50; spark is jumping 1/2-3/4 of an inch. It wil... Trouble codes: P1521 (p1195-), P1195 (p1250-), P1250.		 View
2006 Mazda 6 3.0L Hesitation, Cuts out, MIL Lamp on
Hi folks and thanks for reading this. This car was fine a month ago when it got here and has not been driven. Now we sold it and went to drive it and have these codes. It falls on its face badly and the mitchell diagnosis sends me in circles with no end to it.... Trouble codes: P2179 (Too lean off idle), U0121 (Loss of communication to ABS).		 View
1995 Mercedes-Benz S500 5.0L Low Power
Hi Guys, As usual the ghost stops here again, This 140 body has "low power" on accell. Idles smooth, runs good other than lack of real power. Trans kicks down but Dont go anywhere. Scanned & No codes or check engine light present. We first thought cats clooged...		 View
1995 Mercedes-Benz SL320 3.2L Power Windo
Hello everyone and thanks for the help on this one. We have this 95 convertible in and the drivers window only works very intermittenly. We pulled the door panel and could not get any power to the motor regardless of switch position. We swapped the window swit...		 View
1999 Mitsubishi Mirage 1.5L No Start, Poor Idle Quality, Cuts out, No Throttle Responce
Good Morning I have this problem with this Mitsubishi. It will start when it is floored and idle when floored but not very smoothly. Supposely customer brought vechicle in to another shop for timing belt replacement installed timing belt reconnected battery an...		 View
1996 Pontiac Grand Prix 3.1L lifter
I have this vehicle that came in today not getting any oil to the lifters has 30 psi oil pressue we did and intake job on it back on the 7 of aug and it was very quit when it left was told that yesterday when they started vehicle it started to make noise and w...		 View
1983 Porsche 928 4.5L No Start, Stall
Car will not start periodically and has stalled once on the road. We have been unable to catch it at a time when we can do any testing. The only thing we can verify is that fuel pressure seem good. Can anyone give ,me any direction? Any common problems I can t...		 View
2000 Porsche 911 3.4L convertible top
Hello have a 2000 996 cabriolet with a stuck roof,roof is down and does nothing when switch actuated,this vehicle usually has a hard top installed except for the summer months. There was a bulletin for adjusting micro switches I tried that with no results.Soft...		 View
1999 Saab 9-3 2.0L compressor
Good morning everyone, I have a 99 Saab 9-3 that came in for no a/c. I have no power to the compressor but I can jump the relay and turn on the system and it works fine. My problem is that at the relay I have power on pins 85 & 86 instead of a power and a grou...		 View
1999 Saab 9-5 2.3L turn signals
Hello all, this saab has a problem, but don't they all.. When you turn on the RH turn signal with the head lamps off the LH headlamp and tail lamps flash with the turn signal. if you turn on the head lamps and RH turn,, the RH turn signals flash very dimly bar...		 View
2001 Saturn SL1 1.9L MIL Lamp on
car come in po410 air systems code. test and found pcm not turning on ground to the relay.i could induce ground at pcm connector and make system operate. replace pcm oem part, and had saturn reflash. and now a wk later its back. same code.. my genesus would no... Trouble codes: p0410 (air system).		 View
2002 Saturn SL1 1.9L engine
Well this Saturn came in for a Oil Change and Oil Leak,so i brought it in and found the coolant tank full of oil... Before i tear the head off of this car I just wanted to see if anyone has run into this and maybe found that it was a cracked head or block, I t...		 View
2003 Saturn L300 3.0L No Start
Hello all. This 2003 saturn came to as a no run. cranked over no start. ck on scanner had a po301 and a randum miss fire for codes. had a rpm signal. we ck for fuel psi none. ck for power to pump and ground was ok. with power probe powered up fuel pump and Bea... Trouble codes: p0489 (erg low volts), po638 (po560- tac low volts), po560 (tac low volts), p02101 (tac motor rangeperf), p0700 (trans control fault).		 View
1990 Subaru Loyale 1.8L MIL Lamp on
ih guys, this is a strange problem for me , this car has a code 55 egr temp sensor code , (calif. only ) ,but this car is a federal emissions car. there is no egr temp sensor that i can find and on the ecm where the wire for the sensor should be there is none.... Trouble codes: 55 (egr. temp sensor).		 View
1995 Toyota Tacoma 2.7L Cuts out, MIL Lamp on
This truck came in with a hard start when hot and poor running worse when cold condition. The hard start ended up being the coil. Now I am stuck with a sparatic cutting out under load between 0 - 50 MPH. It doesn't feel like a single cylinder. More like all of... Trouble codes: P0336 (Crank sensor A performance), P0340 (Cam sensor).		 View
1998 Toyota Land Cruiser 4.7L MIL Lamp on
Hello all, This vehicle keeps coming back with a P0446 code in it. We are having difficulty testing the system and finding anything wrong. We have smoke tested the system. I feel like we are missing something or not testing the system correctly. This is the e... Trouble codes: P0446 (evap vent solenoid problem).		 View
2003 Toyota Camry 2.4L engine
help...vehicle presented with milk shake in coolant system. Cyl head sent out & recond, installed new gaskets & head bolts. customer returned 2 days later w/coolant in oil. no overheating problem. customer filled resevoir twice in 2days. head bolts retorqued w...		 View

Fixes & Summaries for All Makes and Models
Fix/Summary Answers
2001 Acura 3.2CL 3.2L wipers
thank you everyone. half of you said the motor was bad and half the switch. we were confused due to all the extra crap in this wiper system. kept it simple and turned wipers on and then off and checked at motor. the motor was still getting power. fault was in ...		 10
1990 Audi V8 Quattro 3.6L MIL Lamp on
Hi sorry it took so long, we did a pin check and found all was good. Tried a good ECM and it took care of it. Thanks to all		 4
1998 BMW 318i 1.9L contol head
HAY GUY'S HAD TO SEND THIS ONE TO THE DEALER AS OUR EQUIPTMENT WOULD NOT REPROGRAM THIS CONTROL HEAD,, ALL IS WELL NOW, THANKS FOR THE HELP.		 4
1999 BMW 740iL 4.4L Oil tailpipe
Well thanks to all for your help, Agian a great learing process. Steve [...] was a great help and wad dead on with this one. Customer okayed work. Went to remove cam covers and what a surprise, well not really, Major sludge every where. I had warned the cu...		 17
1996 Chevrolet Tahoe 5.7L Poor Idle Quality, Cuts out
hello fellow techs.i am closing this due to that i have repaired the problem.i got some very good info on pump pressures and such.i couldnt find a vehicle deterrent on this one.alldata didnt list it either till 1998.i took the air intake assembly off to rechec...		 11
1998 Chevrolet S10 Pickup 4.3L instrument cluster
THANK YOU ALEX! pit3777 hit the nail on the head. Wire broken in harness from 4wd fuse to vcm C4 pin 13. Appears vcm stays in start mode and not run without this feed (doesn't know ignition switch position). Limits serial data. OTC doesn't support ignition clu...		 6
2000 Chevrolet Malibu 3.1L Cuts out, Misfire
well its been a week since i logged on here. this is to all that helped me with this car..thanks for all your help. the car had weak valve springs.the vacuum gauge comfurmed it. needl jumping around, gos to show me that THE BASICS STILL APPLY. thanks alll.. Trouble codes: po300 (multiple miss).		 14
2001 Chevrolet Silverado 6.6L Mechanical
Thanks to all who responded. Most said that the condition is normal and I tend to agree. The only problem is we (the vehicle owner and I) checked 4 other trucks and they were all different. Most would go 1 to 2 inches from the floor, but none would go compl...		 9
2005 Chevrolet Silverado 6.0L odometer
Hello again and thanks for the replies . You all said the same thing. I gave my neighbor a copy of all the replies and he is going to the dealer. I did not want to clear the trip B miles he is going to let the dealer do that. His concern was maybe there was mo...		 6
2000 Chrysler Concorde 2.7L heater
Thanks all for responding so quickly! I checked for codes (none stored) and followed the TSB 24002-04 procedures , removed the M-1 fuse, put it back together, turned ign on waited 4 min, started and drove the car, works fine now! I did recheck codes aft...		 6
2002 Chrysler Voyager 3.3L Cuts out, Misfire
Checked wiring harnesses, found injector harness (engine side) had been routed by exhaust cross over pipe, wires melted together grounding injectors. Awsome help, Thanks Again David Trouble codes: PO172 (Bank 1 Sensor 1 lean), PO300 (Multiple Miss Fire), PO303 (3 Missfire), PO304 (4 Missfire), PO306 (6 Missfire).		 6
2005 Chrysler 300 5.7L over heats
at this time the car has not had any problems with the fans might have fixed it by just removing to check the terminals at the front control module to power distribution center but they have had it out very much either Trouble codes: PO481 (cooling fan 2 high speed relay fault).		 4
2005 Chrysler Town & Country 3.3L abs system
FIRST THANK YOU FOR THE REPLIES. IN SUMMARY OF THE REPLIES IS THAT ONE, THE RR SPEED SENSOR WASN'T READING AT ALL AND SO WE REPLACED THE SENSOR WE THEN SWITCHED REAR SPEED SENSORS RIGHT AND LEFT. STILL HAD THE SAME INTERMITTENT HIGH MPH READING PROBLEM. SECOND...		 4
1998 Dodge Grand Caravan 3.0L 1st
bad filter seal thanks to all...		 3
1998 Dodge Intrepid 3.2L No Start, Misfire, MIL Lamp on
Put a oem ckp sensor in it customer took the car and still had the same problem. Never could get this car to act up for me at the shop, even used it as my everyday car and it never acted up. SO customer as far as i know sold the car... Trouble codes: p0302 (2 misfire), p0300 (random misfire), p1598 (ac pressure sensor high input), p0320 (No crank ref).		 6
2001 Dodge Stratus 2.4L low power
THANKS FOR THE REPLIES, I COULD NOT GET THE CAR TO ACT UP FOR ME BUT I DID RECHECK THE TIMMING MARKS AND THEY WERE DEAD NUTS, COSTUMER HAS HAD THE CAR FOR A WEEK AND HAS HAD NO COMPLAINTS.		 7
2001 Dodge Intrepid 2.7L Poor Idle Quality, Misfire, MIL Lamp on
Here it is. Thanks for all the replies. We double checked all the suggestions from the replies. We sent the PCM out to be tested for a bad coil driver circuit. The rebuilder said it was bad, we purchaced a remanufactured unit.(after we installed and had th... Trouble codes: P0352 (2 ign coil primary circuit).		 6
2003 Dodge Grand Caravan 3.3L Excessive Emissions, Poor Idle Quality, Hesitation, Misfire, MIL Lamp on
thanks to all the replies, after more searching i removed the upper plenum and the injector rail and started spliting the wire loom and there it was. about 2 inches from the connector I found every wire exposed. I ordered a rail harness from the dealer and r... Trouble codes: 203 (cyl. 3 injector control circuit).		 7
2003 Dodge Stratus 2.4L head
As it turns out the rod and main bearings were scorched. The sound was high in the engine but after an exhaustive search I found no fault with the head so we pulled the pan and there the problem was. I assume when it origonally ran hot water and oil mixed and ...		 3
2005 Dodge Sprinter 2.7L Cuts out, MIL Lamp on
Thanks for your replies. I pulled the fuel filter off and looked inside where the water senser goes into it and saw it was full of sediment and had some jell looking stuff in it?? Anyway replaced the filter and the truck runs like new. Trouble codes: P2047 (fuel rail pressure malfunction maximum fuel pressure exceeded), P2051 (fuel rail pressure malfunction maximum fuel pressure exceeded).		 3
1964 Ford Farlain 289CID Shift
First i appreciate all the information i received from everyone. To clarify this is a 1964 Ford Fairlane with a five bolt 289 cid 2bbl engine. All original, still had the tag on the carb. It looks to me that in green dot we should get three shifts and in drive...		 26
1995 Ford Mustang 3.8L Transmission
It looks as if the consensus would be to remove and inspect the bearings. I planned to overhaul the trans if need be. Thanks for the insight into the problem.		 11
1998 Ford Econoline 5.4L no cold air at vents
GREAT ADVISE FROM SEVERAL TECHS. THEY THOUGHT PRESSURE READINGS WERE TOO HIGH AND ADVISE HOSING DOWN THE CONDENSOR TO SEE IF PRESSURES CAME INTO LINE. SURE ENOUGH THEY DID. SUSPECT CLUTCH FAN BAD CUSTOMER IS GOING TO REPLACE AND LET ME KNOW. THANKS AGAIN.		 11
2002 Ford Pickup 5.4L speedometer
FOUND PINCHED WIRE ON CIRCUIT 679 BETWEEN A.B.S. MODULE AND CAB. THANKS FOR THE HELP AND TO ALL THOSE WHO TOOK THE TIME TO READ HELP REQUEST.		 6
2004 Ford Pickup 5.4L Poor Idle Quality, Misfire, MIL Lamp on
we did a compression test only on the #6 cyl because we were afraid to break any more spark plugs and the customer did not want the added expense of that. the comp was 155 lbs dry and went up to 200 lbs wet,a cyl leakdown test showed 23% leakage and we verifie... Trouble codes: p0306 (p0174-), p0174.		 5
1994 GMC Suburban 5.7L Hesitation, rich on start up
Well I had some reallygreat posts to my problem. I do not know what is wrong with this vehicle yet. The customer is will to workwith me one some tests I want to continue to do and if I have a absolute repair I will post it. Just to go over what all was done we...		 22
1997 GMC Pickup 5.7L No Start, Stall
This crazy thing is fixed. It ended up being the fuel pump and sending unit. The wiring at the connector inside the sending unit was melted. The wierd thing is the pump was drawing 9.5 amps and had a perfect wave form right up to the time it quit. Thanks to al...		 11
2000 GMC Savana 5.0L 2-3 shift
I would like to thank everyone that offered help. Alex was right, we did have a bad pcm. We still had the old pcm, which by this time had dried out. I threw it back in and the vehicle was stable enough to drive and voila no 2-3 shift solenoid code. The owner b...		 5
2003 Jaguar S-Type 4.2L Power window and sunroof
Thanks for the responses. Especially to Dan, who offered a lot of advice. But, after trying to initialize the windows, do a hard reset (disconnect the battery) no luck. Called a dealer and they said they have more problems with the drivers side master switch t...		 2
2003 Kia Rio 1.6L flywheel
i took this flywheel to a 3rd machine shop and they were able to machined it. it was a 2 step flywheel they just measured the step and kept the dimensions the same it took about .010 to clean it up. i am not sure why the first 2 shops didnot want to do it. the...		 6
2000 Land Rover Discovery 4.0L engine
Thanks for your assistance - Further investigation, removing timing cover and finding marks bang on, problem being cam gear bolt loose causing groove in cam shaft. Have not fully installed but I do have confidence this is the problem.		 6
2001 Mercury Sable 3.0L Starting
I found that by grounding the signal wire from the PCM to the crank relay(pink wire) the car starts and runs flawlessly. I knew that it could be a bad PCM or the Pats transmiter but had know way of being sure. I called a reliable tech line and they informed me...		 7
2004 MINI Cooper 1.6L evaporator
Not really a fix but a procedural item. thanks to the two techs who responded with the info I needed about removing the instrument carrier Now that I have performed the job I can see why there isn't a shortcut as the HVAC is attatched to the Dash There are con...		 2
2002 Nissan Frontier 2.4L Misfire
Well thanks for all the help. I've been waiting for the car lot to make up their minds and they don't want to spend any money on this truck , or maybe they wanted me to troubleshoot to let thier car lot machanic fix it. Most of the help i recieved said the egr... Trouble codes: p0302 (misfire 2).		 11
1999 Toyota Avalon 3.0L Gas Tank
Have not heard back from my customer on this one, so I will close it out. I Probably scared him off by explaining to him some of the possibilities of dealing with componants that looked like they came off of the Titanic. (Severe Rust) I recieved several rep...		 15
2005 Toyota Corolla 1.8L No Start
all fuses and powers and grounds at ecm were good. did not have bus data coming out. customer had ecm replaced by dealer under warranty. all good.		 10
2001 Volkswagen Passat 1.8L MIL Lamp on
hi fellas , thanks for the help. i tested the maf sensor with my modis . old sensor had low voltage on test 2.86 volts , installed new maf sensor & tested 3.96 volts , i could not check the fuel trims , i hope that this fixes the codes . car is with c... Trouble codes: P1479 (bk. booster vac. sys. mech. malfunction), p1128 (bk 1 long term fuel trim system lean.).		 5
2004 Volvo S60 2.4L Stall
thanks to everybody that took their time to reply. we went ahead and downloaded software upgrades into the engine control module, transmission control module and central electronic module. the electronic throttle module already had the latest software installe...		 4
Prev (Also Available: All, Asian, Chrysler, European, Ford, GM.) Next